Tanks

Pinnacle Mfg., LLC builds tanks at the Boaz, AL plant.  All tanks are constructed with ¼” steel and smooth walls, epoxy lining is also standard.  Models include Pool Tanks, Roll-Off Tanks, Sludge Containers, Mix Tanks, Frac Tanks, Vacuum Containers, Oilfield Tanks, Open Top Tanks, Custom Frac Tanks...  Numerous other options are available including inside manifolds, outside manifolds, gel lines, heat coils, sign plates, additional manways, mixer configurations and additional valves or fittings as requested.

Specs

Example Tank Specifications
Collapse All Expand All

Model:          PT-10             

Capacity: 10,000 BBL / 420,000 Gallons 

Diameter: 80’ Panels: 13                                            

Model:          PT-24             

Capacity: 24,916 BBL / 1,046,472 Gallons

Diameter: 121’    Panels: 20                                            

Model:         PT-42

Capacity: 42,395 BBL / 1,780,590 Gallons

Diameter: 158’ 10”       Panels: 26

Structural:

            ¼” Plate Panels

            4” x 4” x ¼” Outer Tube Frame on Panel

            3” x 3” x ¼” Inner Tube Frame on Panel

Connection:

            Fourteen (14) 1 ¼” Hinge Plates on “Male” Side with 2 ¼” Holes

            Twelve (12) 1 ¼” Hinge Plates on “Female” Side with 2 ¼” Holes

            2” Diameter x 14 ½” Long Connecting Pins

Handling:

            3” x 3” x 3/8” Angle Lifting Bracket

            3/4” Round Bar Lifting Rods in Top Corners

Finish:

            SSPC-SP6 Blast / 4-6 Mils Polyurethane Paint

Piping:

            Per Customer Specifications    

External Stairs to Platform with Interior Ladder

3 Liner Retaining Clamps per Panel

• Capacity: 500 bbl (21,000 gallons)
• Length: 45 ft. Width: 102 in. Height: 114 in.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Fixed Front Stairs with Landing
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: Primer Coat: High Solids Epoxy Primer (4 to 6 mils)
Finish Coat: Polyurethane (2 to 4 mils)
• Manways: One (1) – 20” Diameter – Front
One (1) – 25” Diameter – Passenger Side
Three (3) Unsealed Inspection Hatches on Roof
• Valving: Two (2) 4” Butterfly Valves – Front Drain and Rear Clean-Out
• Feed Line: 3” Rear with Cap
• Manifold: 8” Internal Manifold with Four 4” Butterfly Valve Connections
8” Internal Turndown
• Gel Line: 4” with Butterfly Valve Connection
• Hydrotest: Full Capacity Static Test

• Capacity: 500 bbl (21,000 gallons)
• Length: 45 ft. Width: 102 in. Height: 114 in.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Fixed Front Stairs with Landing
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: 6-8 mils DFT
• Manways: Three (3) – 20” Diameter – Front, Rear, and Roof
One (1) – 25” Diameter – Passenger Side
• Valving: Two (2) 4” Butterfly Valves – Front Drain and Rear Clean-Out
• Feed Line: 3” Rear with Cap
• Manifold: 8” Manifold with Hammerlock Fittings & Four 4” Couplings with Plugs
8” Internal Turndown to Sump
• Gel Line: 4” with Butterfly Valve Connection
• Hydrotest: Full Capacity Static Test


• Capacity: 500 bbl (21,000 gallons)
• Length: 45 ft. Width: 102 in. Height: 114 in.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Fixed Front Stairs with Landing
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: Primer Coat: High Solids Epoxy Primer (4 to 6 mils)
Finish Coat: Polyurethane (2 to 4 mils)
• Manways: Two(2) – 20” Diameter – Front and Rear
One (1) – 25” Diameter – Passenger Side
One (1) – 20” Diameter – Roof
• Valving: Two (2) 4” Butterfly Valves – Front Drain and Rear Clean-Out
• Feed Line: 3” Rear with Cap
• Manifold: 8” Internal Manifold with Four 4” Butterfly Valve Connections
8” Internal Turndown
• Gel Line: 4” with Butterfly Valve Connection
• Hydrotest: Full Capacity Static Test
• Capacity: 500 bbl (21,000 gallons)
• Length: 45 ft. Width: 102 in. Height: 114 in.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Fixed Front Stairs with Landing
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: 6-8 Mils DFT
• Manways: One (1) – 20” Diameter – Front
One (1) – 25” Diameter – Passenger Side
Two (2) Unsealed Inspection Hatches on Roof
• Valving: Two (2) 4” Butterfly Valves – Front Drain and Rear Clean-Out
• Feed Line: 4” Rear with Cap
• Manifold: 8” External Manifold with Hammerlock Fittings & Four 4” Couplings with Plugs
8” Internal Turndown
• Gel Line: 4” with Butterfly Valve Connection – stubbed inside tank with Flange
• Hydrotest: Full Capacity Static Test
• Capacity: 500 bbl (21,000 gallons)
• Length: 45 ft. Width: 102 in. Height: 9 ft. 9 in.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Flat Top with Stairs & Platform on Front Wall
• Suspension &Axle: Hutch 9700 Spring with 22,500 lb. Capacity Axle
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: Polyurethane (4-6 mils) – Your Color
• Manways: Three (3) – 20” Diameter – Roof, Front, & Rear
One (1) – 25” Passenger Side
• Relief Valve: Blaylock Pressure/Vacuum Valve (16 oz.\in2 pressure – 0.4 oz.\in2 vacuum)
• Valving: Two (2) 4” Butterfly Valves – Front Drain & Rear Clean-Out
• Feed Line: 3” Rear with Cap
• Flange Connections: 4” Blind Flange Connection on Roof
• Gel Line: 4” Pipe with 4” Butterfly Valve Connection Mid-High Front Wall
• Manifold: 8” External Manifold with Four (4) 4” Coupling Connections
• Hydrotest: Full Capacity Static Test
• Sign Plates: Installed

• Capacity: 425 bbl (18,000 gallons)
• Length: 45 ft. Width: 102 in. Height: 9 ft.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Rods
• Outer Skin: 3/16” Plate on Sides and Floor
• Stairs: Fixed Front Stairs with Folding Handrail and Handrail on Roof Deck
• Internal Ladder: Located Under Manways
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 14 ply with Steel Wheels
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy
• Exterior Paint: Primer Coat: High Solids Epoxy Primer Finish Coat: Polyurethane
• Fluid Gauge: Level Gauge with Stainless Steel Float Balls
• Manways: Two (2) Marine Hatches on Roof
• Relief Valve: Blaylock Pressure/Vacuum Valve (16 oz.\in2 pressure – 0.4 oz.\in2 vacuum)
• Valving: Two (2) 4” Butterfly Valves – Front & Rear Drain
• Flange Connections:One (1) 4” Flange (Blinded) on Roof
Two (2) 6” Flanges (Blinded) on Roof
• Interstitial Drain: Three (3) 1” Ball Valves - Lower, Front Wall
Three (3) 1” Ball Valves - Lower, Rear Wall
• Hydrotest: Full Capacity Static Test
Air Test Cavity between Walls
• Capacity: 430 bbl – Open Top “Flow Back”
• Length: 45 ft. Width: 102 in. Height: 11 ft. 1 ¼”
• Sides & Floor: ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Passenger Side - Fixed , Non-Folding Handrail
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils) Sides Only – No Coating on Floor
• Exterior Paint: Primer Coat: High Solids Epoxy Primer (4 to 6 mils)
Finish Coat: Polyurethane (2 to 4 mils)
• Manways: Three (3) – 20” Diameter – Rear & 2 Passenger Side
• Valving: Two (2) 4” Butterfly Valves – Front Drain and Rear Clean-Out
• Gas Buster Line: (2) Front Wall, Centered 4” Below Top of Tank – 4” Butterfly Valve Connection – Connected to 8’Pipe Schedule 80 to run 447” Circulation slots per Included drawings.
• Flange Connection: 4” Connection Mid-High on Front Wall
• Hydrotest: Full Capacity Static Test
• Capacity: 430 bbl – Open Top “Gas Buster”
• Length: 45 ft. Width: 102” Height: 116 9/16”
• Sides & Floor: ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Weir: ¼” Plate – A36; Located in Center of tank
• Suspension & Axle: Hutch 9700 Spring, 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Passenger Side - Fixed, Non-Folding Handrail, Walkway Down Passenger Side
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: Finish Coat: Polyurethane (4 to 6 mils) - Black
• Manways: Three (3) – 25” Diameter – Passenger Side
• Valving: Two (2) 4” Butterfly Valves – Front Drain and Rear Clean-Out
Two (2) 4” Butterfly Valves – Mid High with turndown and 12” Below Rail on Front
• Flange Connection:Two (2) 4” Connections on Rear Wall
• Diffusers: Two (2) 10” Diffusers Above Rear of Tank with Slotted Openings & 3/8” Wear Plates in Cap
3” 600# Flange Connections
• Weir: 24” Weir Forward of Diffusers with Gate
• Sight Glass: ¾” Sight Glass on Front Wall with Ball Valve Shut-Offs
• Manifold: 8” External Manifold with Hammer Lock Connections & Four (4) 4” Female Connections with Plugs
• Hydrotest: Full Capacity Static Test
• Capacity: 420 bbl (17,600 gallons)
• Length: 45 ft. Width: 102 in. Height: 9 ft.
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 Spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Front – Fold Down Hand Rail around Perimeter of Roof, Walkway on Roof
• Blast: Exterior – SSPC-SP6
• Exterior Paint: Primer Coat: Ponderosa - Zinc (4 to 6 mils)
Finish Coat: Ponderosa (2 to 4 mils)
• Manways: Six (6) – 22” Diameter – Front, Rear, Side, and Roof w/ removable guards
• Relief Valve: Blaylock Pressure/Vacuum Valve (16 oz.\in2 pressure – 0.4 oz.\in2 vacuum)
• Level Gauge: Level Gauge Brackets Installed, 1-1/2” Coupling on Roof
• Valving: One (1) 4” Butterfly Valves –Rear Clean-Out, One (1) 6” Butterfly Valve-Front
• Flanges: One (1) 4” Blind Flange on Roof – 12” From P/V Valve
• Feed Line: 3” Front with Cap
• Steam Coils: 2” Steam Coils Installed in tank, w/ 2 – 2” Flanged connections on front of tank
• Mixer: One(1) – 3-480v +/- 60 Hz Connection & NEC Motor Control Panel
Four(4) – Hollow Bore Gearbox 72 rpm Output @ 1800 rpm
Four(4) – 10 Hp 1800 rpm Nominal Drive Motor 3-480v 60 Hz
Four(4) – 42” O.D. Mixer Blades & 20” O.D. Mid Blades on 2- 3/8” Shaft
• Hydrotest: Full Capacity Static Test
• Sign Plates: Installed with Customer Supplied Decals
Capacity: 600 bbl (25,200 gallons)
• Length: 53 ft. Width: 102 in. Height: 11 ft. 1 ¼”
• Sides, Floor, Roof ¼” Plate – A36 Smooth Wall / No Internal Bracing
• Suspension: Hutch 9700 spring
• Axle: 5” Round, 71.5” track, 22.5K Capacity
• Wheels & Tires: 11R22.5 – 12 ply with Steel Wheels
• Stairs: Passenger Side – Non-Folding Handrail
• Blast: Interior – SSPC-SP10 Exterior – SSPC-SP6
• Interior Paint: 100% Solids Epoxy – Gray (20 – 25 mils)
• Exterior Paint: Primer Coat: High Solids Epoxy Primer (4 to 6 mils) Finish Coat: Polyurethane (2 to 4 mils)
• Fluid Gauge: Two (2) – 8” S/S Float Balls
• Manways: Three (3) – 20” Diameter – Front, Roof, Rear One (1) – 25” Diameter – Passenger Side
• Relief Valve: Blaylock Pressure/Vacuum Valve (16 oz.\in2 pressure – 0.4 oz.\in2 vacuum)
• Valving: Two (2) 4” Butterfly Valves – Front Drain, Mid High Front
• Feed Line: 3” Front with Cap (Internal)
• Flange Connections: 4” Blind Flange – 2 on Rear Wall & 2 on Roof
• Hydrotest: Full Capacity Static Test
• Sign Plates: Installed with Customer Supplied Decals
• Manifold: Internal Manifold with Four 4” Butterfly Valve Connections
• Gel Line: 4” Gel Line with 4” Butterfly Valve Connection